This is a working overview of sublimation, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2025-12-12. Anything still debated is marked as such rather than presented as settled.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
| Property | Value | Notes |
|---|---|---|
| Process name | Lyophilization or freeze-drying | Both terms appear in technical standards and literature. |
| Phase transition | Sublimation | Solid ice becomes vapor without a liquid step. |
| Typical chamber pressure | 0.05-0.5 mbar | Range depends on product temperature and equipment. |
| Typical product temperature | -40 °C to -10 °C | Measured during primary drying; formulation sets limits. |
| Water content after drying | 0.5-3% w/w | Target varies by material and stability needs. |
Lyophilization, also called freeze-drying, is a dehydration process in which a solvent, usually water, is frozen and then removed by sublimation under reduced pressure. The method preserves heat-sensitive materials that would degrade in conventional drying. Large-scale use grew during the mid-twentieth century for blood plasma and antibiotics, and it later expanded to vaccines, enzymes, foods, and advanced materials. The process produces a dry, porous solid that usually reconstitutes rapidly. It is distinct from simple evaporation because the solvent bypasses the liquid phase during primary removal.
The process generally proceeds in three stages: freezing, primary drying, and secondary drying. During freezing, controlled cooling converts water into ice and may also crystallize or vitrify solutes. In primary drying, the pressure is lowered below the triple point, and heat is supplied so ice sublimes directly to vapor. Secondary drying removes water that remains bound to the solid matrix, yielding a low final water content. Product temperature must stay below the collapse or glass transition temperature to maintain structure. Cycle design therefore balances shelf temperature, chamber pressure, and time.
Freeze-drying is used for materials whose activity or structure depends on low temperature and low water content. Examples include certain biologics, diagnostic reagents, starter cultures, coffee, and porous inorganic precursors. The dried product forms a cake whose porosity aids rapid wetting and dissolution. Main drawbacks are high energy use, long cycle times, and sensitivity to formulation and equipment variation. Questions remain about how freezing rates and ice morphology affect batch uniformity, especially when moving from laboratory to production scale.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Lyophilization, also called freeze-drying, removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts free water into ice and may also produce a glassy phase. Primary drying then lowers chamber pressure so ice sublimes directly to vapor without passing through a liquid stage. Secondary drying raises the temperature modestly to remove bound water. The result is a porous, dry solid that usually reconstitutes quickly. Each stage influences pore structure, residual moisture, and stability.
The physics of lyophilization depends on phase boundaries and heat and mass transfer. During primary drying, heat supplied to the product must equal the latent heat of sublimation, while water vapor moves through the drying cake to the condenser. If shelf temperature or pressure is set too high, the ice front can exceed the collapse temperature, causing meltback or pore collapse. If conditions are too cold, drying slows and costs rise. Formulation excipients, vial geometry, and freezing rate alter these limits.
Although Mexican authorities often distinguish between homicides linked to organized crime and those that are not, the conflict has strained state resources and created an environment of impunity that has worsened crime overall. In 2009, the Mexican attorney general's office claimed that 9 of 10 victims of the Mexican drug war are members of organized crime groups, although other sources have questioned this figure. Deaths among military and police personnel are an estimated 7% of the total. The states that suffer from the conflict the most are Baja California, Guerrero, Chihuahua, Michoacán, Tamaulipas, Nuevo León, and Sinaloa.
=== Forensics === A ninhydrin solution is commonly used by forensic investigators in the analysis of latent fingerprints on porous surfaces such as paper. The amino acids present in the minute sweat secretions that gather on the finger's unique ridges transfer to surfaces that are touched. Exposure of the surface to ninhydrin converts the amino acids into visibly colored products and thus reveals the print. The test solutions suffer from poor long-term stability, especially if not kept cold. To further enhance the ability of ninhydrin, a solution of 1,2-indandione and zinc chloride (IND-Zn) can be used prior to ninhydrin. This sequence leads to greater overall reaction of the amino acids, possibly by IND-Zn helping to release them from the surface for the subsequent ninhydrin reaction.
=== Use by right-to-die societies === High toxicity and relatively easy availability made propoxyphene a drug of choice for right-to-die societies. It is listed in Dr. Philip Nitschke's The Peaceful Pill Handbook and Dr. Pieter Admiraal's Guide to a Humane Self-Chosen Death. "With the withdrawal of the barbiturate sleeping tablets from the medical prescribing list, propoxyphene has become the most common doctor-prescribed medication used by seriously ill people to end their lives."
Sources: en.wikipedia.org
=== Protein evolution and origins of life === In addition to structural bioinformatics, Ben-Tal has worked on protein evolution and the emergence of protein architectures and functions. His laboratory describes this research as addressing how novel protein structures and functions arise during molecular evolution. To trace the evolutionary history of proteins, Ben-Tal, Rachel Kolodny of University of Haifa and coworkers searched among large representative sets of proteins for segments that are similar in sequence (and often also in structure). They presented the results as a similarity network, using a methodology that they tailor-made for this study, showing that many proteins share smaller segments with each other. For example, they observed the same amino acid both within a short theme shared by many proteins and within a longer theme shared only by few. Next, they searched for themes that appear in different sequence and structural contexts within proteins, calling these bridging themes. They found many bridging themes, with an average length of about 40 residues. Interestingly, only about half of these also share a similar structure; the different environment may have induced a conformational change. Some of the bridging themes bind ligands, which attests to their functional importance. Another testimony to the evolutionary importance of these themes is the fact that some of the most ancient protein folds (e.g. Rossmann, P-loop, and TIM-barrel) were found to share them. The bridging themes may offer hints to the emergence of earliest protein families.
==== Reserve ==== On 1 September 2014, 21 and 23 SAS were moved from UKSF. They were placed under command of 1st Intelligence, Surveillance and Reconnaissance Brigade. In 2019 they were moved back to UKSF.
In Australia, the Chinese Medicine Board of Australia regulates acupuncture, among other Chinese medical traditions, and restricts the use of titles like 'acupuncturist' to registered practitioners only. The practice of Acupuncture in New Zealand in 1990 acupuncture was included into the Governmental Accident Compensation Corporation (ACC) Act. This inclusion granted qualified and professionally registered acupuncturists the ability to provide subsidised care and treatment to citizens, residents, and temporary visitors for work- or sports-related injuries that occurred within the country of New Zealand. The two bodies for the regulation of acupuncture and attainment of ACC treatment provider status in New Zealand are Acupuncture NZ, and The New Zealand Acupuncture Standards Authority. At least 28 countries in Europe have professional associations for acupuncturists. In France, the Académie Nationale de Médecine (National Academy of Medicine) has regulated acupuncture since 1955.
Sources: en.wikipedia.org
Conventional drying uses heat to evaporate liquid water, often at temperatures that can degrade sensitive materials. Lyophilization freezes the material first and then removes water by sublimation under vacuum. This avoids prolonged exposure to liquid water and high heat.
Lowering pressure reduces the boiling point of water and allows ice to sublimate at temperatures below freezing. Vacuum also limits convective heat transfer, so heat is usually supplied by shelves or radiation. The pressure must stay below the vapor pressure of ice at the product temperature.
The cycle typically includes freezing, primary drying, and secondary drying. Freezing solidifies water and sets the pore structure; primary drying removes bulk ice; secondary drying removes bound water. Some cycles add annealing or pre-freezing steps.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.