If you have been reading about Primary drying and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-05-21. Where a claim depends on a specific study, the study is described rather than over-claimed.
Reconstitution involves adding a suitable diluent, often sterile water or a buffer, to the dried cake. Gentle swirling or inversion helps dissolve the material without creating excessive foam. The time required for complete dissolution can range from seconds to several minutes and depends on the cake structure and the diluent. Improper reconstitution, such as vigorous shaking or using the wrong diluent, can cause protein aggregation or loss of activity. After reconstitution, the product may have a limited shelf life and should be used according to its labeling.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
A freeze-dryer consists of a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. Vials, ampoules, or bulk trays hold the product during the cycle. The condenser traps water vapor as ice at a temperature lower than the product. Cycle development balances shelf temperature, chamber pressure, and time. Scale-up can be difficult because heat and mass transfer change with equipment size, so process analytical tools and conservative validation are often used.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
Freezing is the first stage and sets the ice structure that later becomes the pore network. The formulation is cooled below its freezing point, often with a controlled ramp, and solutes concentrate as ice forms. Primary drying then lowers chamber pressure and supplies heat to sublime the ice. The product temperature must stay below its collapse or eutectic temperature to prevent structural loss. Secondary drying raises the temperature modestly to remove bound water and achieve a low residual moisture.
| Property | Value | Notes |
|---|---|---|
| Appearance | White to off-white porous cake | Color depends on formulation. |
| Typical storage temperature | 2–8 °C | Refrigerated for many biologics. |
| Residual moisture | <1% to 3% | Low moisture improves stability. |
| Container | Sealed glass vial | Often with rubber stopper and aluminum crimp. |
| Reconstitution time | Seconds to minutes | Varies with cake density and diluent. |
Handling and storage practices aim to keep the cake intact and dry. Vials are typically stored upright at controlled temperatures, often between 2 °C and 8 °C or at -20 °C for longer-term use. Reconstitution involves adding a suitable diluent and gently mixing until the solid dissolves. Shaking or rapid injection of diluent can create foam or damage sensitive molecules. Once reconstituted, the product may require refrigeration and use within a defined period.
Residual moisture is a key quality attribute for lyophilized products. Water that remains after secondary drying can affect chemical stability, cake structure, and shelf life. Karl Fischer titration is a common method for measuring water content in the dried solid. The target range varies by product, but many biologics are dried to between 0.5% and 3% water by weight. Acceptable limits are set during development and confirmed by stability studies.
Stability studies examine how temperature, humidity, and time influence a lyophilized product. Accelerated conditions provide early information about degradation pathways, while long-term studies support shelf-life claims. The glass transition temperature of the dried formulation can indicate its physical stability, and storage above this temperature may increase molecular mobility and lead to collapse or aggregation. Container closure integrity also matters because moisture or oxygen ingress can degrade the product, so vial stoppers and seals are part of the quality system.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
Handling practices aim to prevent moisture ingress and mechanical damage. Vials should remain stoppered and crimped until use, and reconstitution should follow the labeled diluent and volume. Shipping may involve temperature-controlled containers and desiccants, but direct contact between desiccant and product is avoided. Regulatory guidance expects documented storage conditions, excursion assessments, and stability commitments. Open questions remain about how best to predict long-term stability from short accelerated studies for every formulation class.
After lyophilization, the product is usually a porous cake or powder with a large internal surface area. This structure can absorb moisture quickly if exposed to humid air, so vials are sealed under vacuum or an inert gas. Moisture uptake may lower the glass transition temperature of the dried matrix and accelerate chemical or physical degradation. Storage conditions therefore depend on the formulation, container, and intended shelf life. Some products remain stable at room temperature, while others require refrigeration or freezing.
Quality control for lyophilized products includes appearance, cake structure, reconstitution time, pH, residual moisture, and potency. Residual moisture is a key attribute because excess water can reduce stability, while excessively low moisture may cause structural changes or aggregation in some systems. Stability studies compare real-time and accelerated conditions to estimate shelf life. Analytical methods must be validated for the specific matrix, container, and moisture range. Sterility and container integrity are also monitored for sterile products.
=== Antigen discrimination === A unique feature of T cells is their ability to discriminate between healthy and abnormal (e.g. infected or cancerous) cells in the body. Healthy cells typically express a large number of self derived pMHC on their cell surface and although the T cell antigen receptor can interact with at least a subset of these self pMHC, the T cell generally ignores these healthy cells. However, when these very same cells contain even minute quantities of pathogen derived pMHC, T cells are able to become activated and initiate immune responses. The ability of T cells to ignore healthy cells but respond when these same cells contain pathogen (or cancer) derived pMHC is known as antigen discrimination. The molecular mechanisms that underlie this process are controversial.
La Familia Michoacana was a drug cartel based in Michoacán between at least 2006 and 2011. It was formerly allied with the Gulf Cartel and Los Zetas, but split off to become an independent organization. La Familia Michoacana was the first cartel targeted by President Calderón's security strategy, beginning with Operation Michoacán in December 2006. Between 2009 and 2010, joint U.S.–Mexican operations led to the arrest of hundreds of La Familia members and the reported death of founder Nazario Moreno González ("El Más Loco"). The group soon split between the Knights Templar Cartel and a faction led by José de Jesús Méndez Vargas ("El Chango"), who was arrested in 2011, after which authorities declared La Familia dismantled, leaving the Knights Templar as its de facto successor. In February 2010, La Familia allied with the Gulf Cartel against Los Zetas and the Beltrán-Leyva Cartel. La Nueva Familia Michoacana emerged from splinters of La Familia in the early 2010s, rebranding while continuing operations in Michoacán and Guerrero, and clashing with the Jalisco New Generation Cartel.
The triple quadrupole mass spectrometer essentially operates under the same principle as the single quadrupole mass analyzer. Each of the two mass filters (Q1 and Q3) contains four parallel, cylindrical metal rods. Both Q1 and Q3 are controlled by direct current (dc) and radio-frequency (rf) potentials, while the collision cell, q, is only subjected to RF potential. The RF potential associated with the collision cell (q) allows all ions that were selected for to pass through it. In some instruments, the normal quadrupole collision cell has been replaced by hexapole or octopole collision cells which improve efficiency. Unlike traditional MS techniques, MS/MS techniques allow for mass analysis to occur in a sequential manner in different regions of the instruments. The TQMS follows the tandem-in-space arrangement, due to ionization, primary mass selection, collision induced dissociation (CID), mass analysis of fragments produced during CID, and detection occurring in separate segments of the instrument. Sector instruments tend to surpass the TQMS in mass resolution and mass range. However, the triple quadrupole has the advantage of being cheaper, easy to operate and highly efficient. Also, when operated in the selected reaction monitoring mode, the TQMS has superior detection sensitivity as well as quantification. The triple quadrupole allows the study of low-energy low-molecule reactions, which is useful when small molecules are being analyzed.
== Safety == Theacrine has demonstrated clinical safety and non-habituating effects in healthy humans over eight weeks of daily use at up to 300 mg/day. Moreover, there was no evidence of the tachyphylaxis typical of neuroactive agents like caffeine and other stimulants. In animal studies, theacrine has an LD50 of 810 mg/kg, compared to 265 mg/kg for caffeine.
A definitive diagnosis is made after based on growth hormone concentrations or increased IGF-1 levels. In male dogs with no history of progestogen administration the possibility of a pituitary tumour needs to be examined via CT/MRI. In cats with difficult to manage diabetes but no other signs of hypersomatotropism, the potential for other causes of poor glycaemic control need to be considered.
Sources: en.wikipedia.org
The defining feature of periodontitis is connective tissue attachment loss which may manifest as deepening of periodontal pockets, gingival recession, or both. This loss of support for the teeth is essentially irreversible damage. Chronic periodontitis is generally slow to moderate in terms of disease progression, although short bursts of increased tissue destruction may occur. Ultimately, tooth loss may occur if the condition is not halted. It is termed localized when less than 30% of sites around teeth are involved, and generalised when more than 30% are involved. clinical attachment loss can be used to determine the severity of the condition, where 1–2 mm is slight, 3–4 mm is moderate and more than 5mm is severe.
It is a colourless paramagnetic gas that, being thermodynamically unstable, decomposes to nitrogen and oxygen gas at 1100–1200 °C. Its bonding is similar to that in nitrogen, but one extra electron is added to a π* antibonding orbital and thus the bond order has been reduced to approximately 2.5; hence dimerisation to O=N–N=O is unfavourable except below the boiling point (where the cis isomer is more stable) because it does not actually increase the total bond order and because the unpaired electron is delocalised across the NO molecule, granting it stability. There is also evidence for the asymmetric red dimer O=N–O=N when nitric oxide is condensed with polar molecules. It reacts with oxygen to give brown nitrogen dioxide and with halogens to give nitrosyl halides. It also reacts with transition metal compounds to give nitrosyl complexes, most of which are deeply coloured. Blue dinitrogen trioxide (N2O3) is only available as a solid because it rapidly dissociates above its melting point to give nitric oxide, nitrogen dioxide (NO2), and dinitrogen tetroxide (N2O4). The latter two compounds are somewhat difficult to study individually because of the equilibrium between them, although sometimes dinitrogen tetroxide can react by heterolytic fission to nitrosonium and nitrate in a medium with high dielectric constant. Nitrogen dioxide is an acrid, corrosive brown gas. Both compounds may be easily prepared by decomposing a dry metal nitrate. Both react with water to form nitric acid.
=== Inference === Variant genetic codes used by an organism can be inferred by identifying highly conserved genes encoded in that genome, and comparing its codon usage to the amino acids in homologous proteins of other organisms. For example, the program FACIL infers a genetic code by searching which amino acids in homologous protein domains are most often aligned to every codon. The resulting amino acid (or stop codon) probabilities for each codon are displayed in a genetic code logo. As of January 2022, the most complete survey of genetic codes is done by Shulgina and Eddy, who screened 250,000 prokaryotic genomes using their Codetta tool. This tool uses a similar approach to FACIL with a larger Pfam database. Despite the NCBI already providing 27 translation tables, the authors were able to find new 5 genetic code variations (corroborated by tRNA mutations) and correct several misattributions. Codetta was later used to analyze genetic code change in ciliates.
=== Drift tube ion mobility spectrometry === Drift tube ion mobility spectrometry (DTIMS) measures how long a given ion takes to traverse a given length in a uniform electric field through a given atmosphere. In specified intervals, a sample of the ions is let into the drift region; the gating mechanism is based on a charged electrode working in a similar way as the control grid in triodes works for electrons. For precise control of the ion pulse width admitted to the drift tube, more complex gating systems such as a Bradbury–Nielsen or a field switching shutter are employed. Once in the drift tube, ions are subjected to a homogeneous electric field ranging from a few volts per centimetre up to many hundreds of volts per centimetre. This electric field then drives the ions through the drift tube where they interact with the neutral drift molecules contained within the system and separate based on the ion mobility, arriving at the detector for measurement. Ions are recorded at the detector in order from the fastest to the slowest, generating a response signal characteristic for the chemical composition of the measured sample. The ion mobility K can then be experimentally determined from the drift time tD of an ion traversing within a homogeneous electric field the potential difference U in the drift length L.
=== 19th century === Originally a farmer from Iowa, Abner Hackleman arrived as the first European American settler in 1845. Taking up a land claim for himself, Hackleman asked Hiram N. Smead to hold another for him until his son arrived from Iowa. In 1846, a year after arriving in Oregon, Hackleman died while returning to Iowa to fetch his family. In 1847 a pair of brothers, Walter and Thomas Monteith, settled in the area, after traveling by ox team along the Oregon Trail from their native state of New York. They were a family of early prominence in the area; in 1848, they bought a claim of 320 acres (1.3 km2) from Hiram Smead for $400 and a horse; they plotted out 60 acres (240,000 m2) for the town site. They named the city "Albany" after their hometown of Albany in New York. During the same period, Hackleman's son Abram reached his father's original land claim and built a log house in an oak grove still known as Hackleman's Grove. He later built a house, which still stands at the corner of Fifth and Jackson. The small settlement that formed on the Hackleman land became known as the community of Takenah in 1849.
Sources: en.wikipedia.org
== Selected publications == Bence, Kendra K.; Delibegovic, Mirela; Xue, Bingzhong; Gorgun, Cem Z.; Hotamisligil, Gokhan S.; Neel, Benjamin G.; Kahn, Barbara B. (2006). "Neuronal PTP1B regulates body weight, adiposity and leptin action". Nature Medicine. 12 (8): 917–924. doi:10.1038/nm1435. ISSN 1546-170X. PMID 16845389. S2CID 10654045. Delibegovic, Mirela; Zimmer, Derek; Kauffman, Caitlin; Rak, Kimberly; Hong, Eun-Gyoung; Cho, You-Ree; Kim, Jason K.; Kahn, Barbara B.; Neel, Benjamin G.; Bence, Kendra K. (2009-03-01). "Liver-Specific Deletion of Protein-Tyrosine Phosphatase 1B (PTP1B) Improves Metabolic Syndrome and Attenuates Diet-Induced Endoplasmic Reticulum Stress". Diabetes. 58 (3): 590–599. doi:10.2337/db08-0913. ISSN 0012-1797. PMC 2646057. PMID 19074988. Delibegovic, Mirela; Bence, Kendra K.; Mody, Nimesh; Hong, Eun-Gyoung; Ko, Hwi Jin; Kim, Jason K.; Kahn, Barbara B.; Neel, Benjamin G. (2007-11-01). "Improved Glucose Homeostasis in Mice with Muscle-Specific Deletion of Protein-Tyrosine Phosphatase 1B". Molecular and Cellular Biology. 27 (21): 7727–7734. doi:10.1128/MCB.00959-07. ISSN 0270-7306. PMC 2169063. PMID 17724080.
=== Story === The game features three different playable characters, each with their own story arcs that intersect throughout the game: Arthur's Story: Arthur Hastings (Alex Wyndham) works as a censor approving or redacting old news articles from Wellington Wells' Department of Archives, Printing, and Recycling. While working, he comes across a news clipping of him and his older brother Percy (Bradley Henderson) after World War II. At this point, Arthur can either take his Joy (which ends the game) or refuse it, wanting to remember Percy. If the latter choice is taken, Arthur attends an office party with his boss, Victoria Byng (Katherine Kingsley), and watches in horror as Victoria and his co-workers consume a rat that they hallucinate to be a candy-filled piñata. He is then called out as a Downer and chased by two police constables, ending up in the Garden District, now populated by Wastrels. Arthur resolves to escape Wellington Wells and find Percy. With the assistance of various characters, Arthur works his way through the districts uncovering certain truths along the way. It is eventually revealed that the "Very Bad Thing" was when the population of Wellington Wells turned over all children under the age of 13 years to the Germans in exchange for their freedom. Arthur discovers that the German tanks used to threaten the town into compliance were actually dummy tanks made of papier-mâché, and that while the populace could have resisted, they did not out of fear.
=== Derivatives === HMF itself has few applications. It can however be converted into other more useful compounds. Of these the most important is 2,5-furandicarboxylic acid, which has been proposed as a replacement for terephthalic acid in the production of polyesters. HMF can be converted to 2,5-dimethylfuran (DMF), a liquid that is a potential biofuel with a greater energy content than bioethanol. Hydrogenation of HMF gives 2,5-bis(hydroxymethyl)furan. Acid-catalysed hydrolysis converts HMF into gamma-hydroxyvaleric acid and gamma-valerolactone, with loss of formic acid.
autophagy Also autophagocytosis. The orderly autolytic degradation and recycling of dysfunctional or unnecessary cellular components by the cell's own enzymes as part of a carefully regulated, lysosome-dependent pathway. Autophagic programs play important roles in nutrient-deprived and senescent cells but also help maintain homeostasis in healthy cells.
A 2019 YouGov poll found that 7 out of 10 millennials in the United States would vote for a socialist presidential candidate and 36% had a favorable view of communism. An earlier 2019 Harris Poll found that socialism is more popular with women than men, with 55% of women between the ages of 18 and 54 preferring to live in a socialist society while a majority of men surveyed in the poll chose capitalism over socialism. Although there is no agreement on the meaning of socialism in those polls, there has been a steady increase of support for progressive reforms proposed by democratic socialist legislators such as the United States National Health Care Act to enact universal single-payer health care and the Green New Deal. In November 2018, Alexandria Ocasio-Cortez and Rashida Tlaib, who are members of the Democratic Socialists of America (DSA), the largest socialist organization in the United States, which pushes for policy reforms alongside non-governmental action, were elected to the House of Representatives while eleven DSA candidates were elected to state legislatures, a breakthrough in modern American politics. As of July 2023, there are now five DSA members and two non-DSA democratic socialists in the House of Representatives, one democratic socialist in the U.S. Senate, 51 DSA members in state legislatures, and 132 DSA members in local offices.
Sources: en.wikipedia.org
Lyophilized products should be stored in airtight containers, protected from moisture and light, at the temperature specified by the manufacturer. Many require refrigeration at 2–8 °C, while some need frozen storage. Always check the product label for specific conditions.
Moisture can cause the porous cake to collapse, increase molecular mobility, and accelerate chemical degradation. It may also promote microbial growth if the product lacks preservatives. Proper sealing and handling are essential to maintain stability.
Some formulations contain labile biological molecules that degrade even in the dry state at higher temperatures. Others have a low glass transition temperature, meaning the cake can soften or collapse at room temperature. Cold storage reduces molecular motion and slows degradation.
Yes, the terms are generally interchangeable. Lyophilization is more common in pharmaceutical and laboratory contexts, while freeze-drying appears widely in food science and general writing. Both describe removal of solvent by sublimation under vacuum after freezing.