If you have been reading about Primary drying and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-03-31. Where a claim depends on a specific study, the study is described rather than over-claimed.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
Quality control for freeze-dried lots combines visual inspection with instrumental tests. Cake appearance, color, and shrinkage are recorded against a reference, while residual moisture is measured by Karl Fischer titration or loss on drying. Thermal analysis can reveal phase transitions and crystallization events, and X-ray diffraction distinguishes amorphous from crystalline solids. Microbiological tests and container closure integrity checks are also routine for sterile products. Analytical methods must be validated for the matrix, because excipients and low moisture can affect accuracy. Open questions include how best to predict long-term stability from short-term data.
Lyophilized solids are often hygroscopic, so handling occurs in controlled low-humidity areas or glove boxes when the material is exposed. Vials remain sealed with elastomeric stoppers and aluminum crimps until use, because airborne moisture can raise residual water and shorten shelf life. The porous cake is fragile and may crack, shrink, or powder during transport. Personnel typically avoid repeated warming and cooling of sealed units, which can draw moisture through closures. These practices aim to preserve the low water content achieved during drying.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Reconstitution involves adding a suitable diluent, often sterile water or a buffer, to the dried cake. Gentle swirling or inversion helps dissolve the material without creating excessive foam. The time required for complete dissolution can range from seconds to several minutes and depends on the cake structure and the diluent. Improper reconstitution, such as vigorous shaking or using the wrong diluent, can cause protein aggregation or loss of activity. After reconstitution, the product may have a limited shelf life and should be used according to its labeling.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Freeze-dried materials are hygroscopic to varying degrees and can take up moisture after drying. Storage therefore often uses sealed glass vials, rubber stoppers, and crimp seals to limit contact with ambient humidity. A desiccant may be included for moisture-sensitive products, although it is not universal. Controlled room temperature is sufficient for many lyophilizates, while others require refrigeration or freezing. Moisture ingress remains a primary cause of cake collapse, chemical degradation, and loss of reconstitution performance.
Quality assessment of a lyophilized product includes cake appearance, residual moisture, reconstitution time, and container closure integrity. A uniform, porous cake suggests that freezing and drying stayed within the formulation's design space. Cracks, shrinkage, meltback, or a glassy film can indicate thermal abuse or a formulation problem. Analysts also test for subvisible particles and sterility when the product requires those specifications. Visual inspection alone cannot confirm biological activity or chemical stability, so it is combined with analytical methods.
The "Cave of the Statues" (Statuenhöhle) was a magnificent cave, located next to the "Peacock Cave" (Cave 76). It is a "colossal image cave", with no niche in the main cella, but a podium on which a colossal standing statue of the Buddha probably stood. In an atypical design, the back corridor is quite large and wider than the main cella, with a width of 8.70 meters (342 inches), for a height of 5.10 meters (200 inches). Only seven other "Colossal image caves" are known in Kizil, including caves 47, 48, 70, 136, 139, 146. They are characterized by a very tall main cella designed to accommodate a gigantic image of the Buddha, the height of the cella reaching around 5 meters (16 feet) and sometimes as high as 16.5 meters (650 inches) (such as in cave 47), and also a rather tall back room (often around 5–6 meters; around 200 inches high). The numerous statues of the cave were made of clay and straw, fibers or hair for reinforcement, and often dated to the 6th century CE, but now rather dated to 375–400 CE in conjunction with carbon dates. Many of the statues were made from molds, which had Sanskrit names on them, which are probably the names of the crafsmen or the owners. The cave is a "central pillar" cave, but the roof of the main cella, which formed a vault culminating at around 6 meters (20 feet), has entirely collapsed. A few paintings remained on the walls of the main cella: they were sermons of the Buddha organized in several rows, the size of each of these pictures being 1.34 metres (52 inches) wide and 96 cm (38 inches) high.
=== Physical === Most of the physical properties of astatine have been estimated (by interpolation or extrapolation), using theoretically or empirically derived methods. For example, halogens get darker with increasing atomic weight—fluorine is nearly colorless, chlorine is yellow-green, bromine is red-brown, and iodine is dark gray/violet. Astatine is sometimes described as probably being a black solid (assuming it follows this trend), or as having a metallic appearance (if it is a metalloid or a metal). Because it has a lower vapor pressure than iodine, astatine sublimes, as expected. Half of a given quantity of astatine will vaporize in approximately an hour if put on a clean glass surface at room temperature. The absorption spectrum of astatine in the middle ultraviolet region has lines at 224.401 and 216.225 nm, suggestive of 6p to 7s transitions. The structure of solid astatine is unknown. As an analog of iodine it may have an orthorhombic crystalline structure composed of diatomic astatine molecules, and be a semiconductor (with a band gap of 0.7 eV). Alternatively, if condensed astatine forms a metallic phase, as has been predicted, it may have a monatomic face-centered cubic structure; in this structure, it may well be a superconductor, like the similar high-pressure phase of iodine. Metallic astatine is expected to have a density of 8.91–8.95 g/cm3. Evidence for (or against) the existence of diatomic astatine (At2) is sparse and inconclusive.
Phenelzine requires attention to dietary tyramine and clinically important drug interactions, but severe tyramine-related hypertensive reactions are uncommon when dietary and medication precautions are followed. Modern food standards have substantially reduced tyramine levels in many foods compared with the 1950s and 1960s, making excessive tyramine ingestion less likely than in earlier decades. The highest-risk foods are generally those that are fermented, matured, or spoiled, including some aged cheeses, some artisan beers, fermented meats, and fermented products such as soy sauce, miso, tempeh, sauerkraut, Marmite, and kimchi. Because inhibition of monoamine oxidase reduces the breakdown of dietary tyramine in the gastrointestinal tract and liver, excessive tyramine intake can raise blood pressure through peripheral norepinephrine release. If this causes a marked blood-pressure rise, the reaction is usually self-limiting and typically reaches its maximum within about 2 hours. Modern guidance advises against rapid blood-pressure reduction outside appropriate medical supervision, because overtreatment can cause hypotensive overshoot; sublingual nifedipine is specifically discouraged. The Cambridge Prescriber's Guide recommends benzodiazepine administration with blood-pressure monitoring, with emergency clinicians using clinical judgment in severe cases and considering short-acting agents such as phentolamine when additional treatment is needed.
==== Genetic defects ==== Genetically confirmed diagnoses of diseases affecting vitamin B6 metabolism (ALDH7A1 deficiency, pyridoxine-5'-phosphate oxidase deficiency, PLP binding protein deficiency, hyperprolinaemia type II and hypophosphatasia) can trigger vitamin B6 deficiency-dependent epileptic seizures in infants. These are responsive to pyridoxal 5'-phosphate therapy.
The supporters of the war claimed that it "pitted British Freedom, justice and civilization against Boer backwardness". The French Canadians' opposition to the Canadian involvement in a British 'colonial venture' eventually led to a three-day riot in Quebec. Many Canadian soldiers did not actually see combat since many arrived around the time of the signing of the Treaty of Vereeniging on 31 May 1902.
Sources: en.wikipedia.org
The injury was determined to be caused by the full power of the magnetron; the pulsating sensation was caused either by the stirrer (a mechanical mirror distributing the microwave beam across the oven space to prevent formation of hot and cold spots), or by the arterial pulsation in combination with increased nerve sensitivity. Damage to the A beta fibers, A delta fibers, and group C nerve fibers was the cause of the burning sensation. The increased hypersensitivity to radiant heat is caused by the damage to the A beta, A delta, and polymodal nociceptors (the group C fibers); this damage is induced by a single-time overheating of the skin to 48.5–50 °C, and the resulting sensitivity persists for a long time. Degeneration of the alpha motor neurons is also caused by the exposure to heat and radiation. Most of the major nerve trunks were not affected. Damage to the A beta fibers (located in the skin), discovered by the two-point discrimination test, is permanent; the Pacinian corpuscles, Meissner corpuscles, and Merkel nerve endings, which degenerated after denervation, do not regenerate. The sympathetic nervous system was involved as well; the reduction in active sweat glands was caused by destruction of their innervation, the initial edema and reddening was also caused by sympathetic nerve damage. In 1983, a 35-year-old male was heating a sandwich in a microwave oven at work. After opening the door, the magnetron did not shut off and his right hand was exposed to microwave radiation as he retrieved the sandwich.
The same cannot be said for human bone collagen, as δ18O values in collagen seem to be impacted by drinking water, food water, and a combination of metabolic and physiological processes. δ18O values from bone minerals are essentially an averaged isotopic signature throughout the entire life of the individual. While carbon and nitrogen are used primarily to investigate the diets of ancient humans, oxygen isotopes offer insight into body water at different life stages. δ18O values are used to understand drinking behaviors, animal husbandry, and track mobility. 97 burials from the ancient Maya citadel of Tikal were studied using oxygen isotopes. Results from tooth enamel identified statistically different individuals, interpreted to be individuals from Maya lowlands, Guatemala, and potentially Mexico. Historical context combined with isotopic data from burials were used to argue that migrant individuals were a part of lower and higher social classes within Tikal. Female migrants who arrived in Tikal during Early Classic period could have been the brides of Maya elite.
=== Research focus === NCCIH funds research into complementary and alternative medicine, including support for clinical trials of CAM techniques. The four primary areas of focus are research, research training and career development, outreach, and integration. NCCIH divides complementary and alternative medicine into natural products, including dietary supplements and herbal supplements; mind and body practices, including meditation, yoga, qigong, acupuncture and spinal manipulation (both chiropractic and osteopathic); and other approaches, such as homeopathy, naturopathy, Traditional Chinese Medicine (TCM), and ayurveda.
ABS-201 is an AI-designed monoclonal antibody against the prolactin receptor (PRLR) currently in Phase 1/2a clinical trial for the treatment of androgenic alopecia (pattern hair loss) and endometriosis. It is taken by subcutaneous injection. ABS-201 is a possible first-in-class drug with a novel mechanism of action in the potential treatment of hair loss. ABS-201 is under development by Absci. It is believed that ABS-201 works by activating dormant hair follicles and causing them to move from the telogen phase to the anagen phase. In human ex vivo scalp model studies, ABS-201 stimulated hair regrowth, prolonged anagen phase, blocked catagen phase, inhibited telogen effluvium, and blocked hair from losing color. ABS-201 has been found to produce robust hair regrowth as compared with minoxidil in mice and balding macaques. The clinical trial for ABS-201 is being overseen by prominent hair loss researcher Rodney Sinclair, one of the principal investigators in minoxidil clinical trials. The chemical structure of the drug does not yet appear to have been disclosed.
Sources: en.wikipedia.org
==== Notable incidents ==== The state of Florida used midazolam to execute William Frederick Happ in October 2013. The state of Ohio used midazolam in the execution of Dennis McGuire in January 2014; he was heavily anesthetized and unconscious within 4 minutes of starting the administration of midazolam and 20 more minutes after that point before he was declared medically dead. Controversy arose after he was observed gasping and appeared to choke during that time according to reporters who were allowed to be present, leading to questions about the dosing and timing of the drug administration, as well as the choice of drugs. The usage of midazolam in executions became controversial after condemned inmate Clayton Lockett apparently regained consciousness and started speaking midway through his 2014 execution when the state of Oklahoma attempted to execute him with an untested three-drug lethal injection combination including 100 mg of midazolam. Prison officials reportedly discussed taking him to a hospital before he was pronounced dead of a heart attack 40 minutes after the execution began. An observing doctor stated that Lockett's vein had ruptured. It is not clear whether his death was caused by one or more of the drugs or by a problem in the administration procedure, nor is it clear what quantities of vecuronium bromide and potassium chloride were released to his system before the execution was cancelled.
Glipizide, sold under the brand name Glucotrol among others, is an anti-diabetic medication of the sulfonylurea class used to treat type 2 diabetes. It is used together with a diabetic diet and exercise. It is not indicated for use by itself in type 1 diabetes. It is taken by mouth. Effects generally begin within half an hour and can last for up to a day. Common side effects include nausea, diarrhea, low blood sugar, and headache. Other side effects include sleepiness, skin rash, and shakiness. The dose may need to be adjusted in those with liver or kidney disease. Use during pregnancy or breastfeeding is not recommended. It works by stimulating the pancreas to release insulin and increases tissue sensitivity to insulin. Glipizide was approved for medical use in the United States in 1984. It is available as a generic medication. In 2023, it was the 42nd most commonly prescribed medication in the United States, with more than 15 million prescriptions.
In 2011, tourists visiting Ghana numbered 1,087,000, with arrivals including South Americans, Asians, Europeans, and North Americans. Among the attractions and tourist destinations are waterfalls such as Kintampo waterfalls and the largest waterfall in west Africa, Wli waterfalls, the coastal palm-lined sandy beaches, caves, mountains, rivers, and reservoirs and lakes such as Lake Bosumtwi and the largest human-made lake in the world by surface area, Lake Volta, dozens of forts and castles, World Heritage Sites, nature reserves and national parks. Castles include Cape Coast Castle and the Elmina Castle. Castles mark where blood was shed in the slave trade and preserve and promote the African heritage stolen and destroyed through the slave trade. The World Heritage Convention of UNESCO named Ghana's castles and forts as World Heritage Monuments: "The Castles and Forts of Ghana shaped not only Ghana's history but that of the world over four centuries as the focus of first the gold trade and then the slave trade. They are a significant and emotive symbol of European–African encounters and of the starting point of the African Diaspora." The World Economic Forum statistics in 2010 showed that out of the world's favourite tourist destinations, Ghana was ranked 108th out of 139 countries. The country had moved two places up from the 2009 rankings. In 2011, Forbes magazine published that Ghana was ranked the 11th most friendly country in the world. The assertion was based on a survey in 2010 of a cross-section of travellers.
relaxation of muscle spasms prevention and retardation of disuse atrophy increase of local blood circulation muscle rehabilitation and re-education electrical muscle stimulation maintaining and increasing range of motion management of chronic and intractable pain including diabetic neuropathy acute post-traumatic and post-surgical pain post-surgical stimulation of muscles to prevent venous thrombosis wound healing drug delivery There is limited evidence supporting electrotherapy, specifically in treating musculoskeletal, osteoarthritis, fibromyalgia, neck pain, lumbopelvic pain, and ulcer conditions. Some of the treatment effectiveness mechanisms are little understood. The natural neurostimulation hypothesis explains the therapeutic effect by the fact that energy stimuli induce mitochondrial stress and microvascular vasodilation. Since healthy neurostimulation should emulate the physical characteristics of a mother's care for her fetus during pregnancy scaled to the treatment parameters of the specific patient, but many techniques of electrotherapy do not consider this, the hypothesis claims that their effectiveness and some practices associated with their use are still anecdotal.
By 1986–1987, the Reagan administration increasingly employed public rhetorical challenges that emphasized human rights and political choice as tests of Soviet reform, during which the American president used a symbolic address to gauge the credibility of Gorbachev's agenda. The most overt example occurred when Reagan challenged Gorbachev on June 12, 1987 to go further with his reforms and democratization by tearing down the Berlin Wall. In a speech at the Brandenburg Gate next to the wall, Reagan stated:
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
Karl Fischer titration is widely used because it is specific for water and works at low levels. Loss on drying is simpler but less specific, since volatile solvents or decomposition products can also be lost.